Air Compressors

Clear air hose plastic tubing. Used to give you extra length between your Powercarver and air compressor. Accepts 1/8 inch hose barbs.

In stock

Minimum quantity for "Air Hose Clear Tubing, only $0.95 per foot!" is 10.


Brass Hose Barb Splicer
$5.95   $4.95

This brass hose barb splicer allows you to connect two air hoses together by pushing the hose on to the barb. The splicer is designed for air hose with 1/8 inch inside diameter, like the hose that comes with the Powercarver and extra length of hose in this section. This splicer is all brass construction, will not rust or corrode. Precision machined to high quality standards.

In stock
+

Female Brass Industrial Plug 1/4 NPT. Makes it easy to connect your air hose to your air compressor. If you have our CAT-1601a air compressor with a quick release, get this matching part. It makes your air connections a snap!

In stock
+

This strong, flexible polyurethane tubing is 5 to 10 times more wear and abrasion-resistant than other tubing, and lighter weight. Perfect for connecting between your air compressor and water trap. Fits 1/8 inch hose barbs. Maximum pressure of 180 PSI, Burst Pressure 720 PSI, Temp Range -68 To 140 F, Color Clear Blue (may vary). Meets NSF 61 Standards.

In stock

Minimum quantity for "High Quality Air Hose Polyurethane Tubing, only $1.50 per foot!" is 10.


Male Brass Hose Barb 1/4 NPT. Push on to 1/8 to 3/16 inch inside diameter hose. Threads are 1/4 NPT. Connect to your air compressor or filter and air hose.

In stock
+

This combination air filter and water trap removes dirt & debris larger than 5 microns and helps catch condensed water. A must for improving the life of your turbine bearings. For best use, have at least 10 feet of hose between your air compress and this air filter/water trap. This will ensure the air has cooled and the water vapor has condensed where it can be collected by the water trap. Easy to connect. Your air compressor connects to the "IN" port and the Powercarver hose barb connect to the "OUT" port. When water collected is about 1/2 full in the clear bowl, open the release valve to drain the water. Remember to order 2 brass hose barbs to connect your air hose. The hose barbs are 1/4 NPT and push onto 1/8 inch inside diameter hose.

In stock

Quick-Disconnect Coupling
$9.95   $8.95

Valveless fittings are completely interchangeable. Fitting halves seal with a twist; replaceable O-rings eliminate leaks. Use to disconnect tool from air supply or add cleaner/lube. Fitting is 1/8" ID (fits our air hose). Rated to 100 psi.

In stock
+

Vary the speed of your carver hands-free! This variable speed foot control pedal is a must have! It allows you to change the speed seamlessly with an easy to press foot pedal, leaving your hands free to hold the tool and your work simultaneously without interruptions from fumbling with hand controls. From off to full speed and everything in between, you'll be amazed how often you change your carving speed from moment to moment. With just a little change in foot pressure, you can change the speed to carve critically fine details or press down for fast carving. This foot pedal connects into your air hose to control the speed of your carver and comes with two brass hose barbs for easy hook-up. Just push your air hose onto the barbs and you have instant speed control. Your carving tool is off until you apply foot pressure to the pedal. The more you push the pedal, the faster your carver turns. The foot pedal uses an actual control valve connected to a long throw pedal to vary the air flow, unlike other foot pedals that pinch the air hose and can cause leaks and foot fatigue. Once you use a foot pedal like this, you'll wonder how you ever carved without it. This foot pedal is industrial grade and will last a lifetime.

In stock
+

Teflon® tape, also know as PTFE tape, is used to make a tight seal the threads for our brass hose barbs. With the threads facing you, wrap 3 turns of tape clockwise. Make sure the tape does not extend over the end of the horse barb, this will prevent blockage.

In stock
+

In stock is our very popular quiet, but powerful energy efficient oil-less air compressor with more than ample air supply for your PowerCarver, Powercrafter or Turbo Carver. The 1610A Ultra Quiet Air Compressor is designed to be one of the quietest air compressors in the industry having only 60 decibels of sound. This air compressor makes less sound than a normal conversation (65 decibels).

In stock

Designed for people who love to carve non-stop. If you're a Wood Piercing or Egg Carvers who can carve for hours at a time, this air compressor is for your. Since it only takes 20 seconds to refill, you're assured you can carve for hours on end without your air compressor overheating. With two tanks and two quick connects, you can connect your turbine carver and dust blow gun at the same time. The 4620A is a popular ultra quiet and very powerful energy efficient oil-less air compressor. This means you get clean air, a must when using turbine carvers. The high output "piston" air compressor requires less electrical power, yet it has more than ample air supply for your PowerCarver, Powercrafter or Turbo Carver. This compressor works perfectly with the PowerCarver and being only 70db, makes it easy on your ears (great for apartments, shows or classrooms where you need a quiet compressor) and easy on your pocketbook. This air compressor is designed to provide smooth and consistent dry airflow to your turbine carver because the tank captures the water that would otherwise enter your carver. Just connect the hose to the compressor and turn it on, turn the dial to 45psi and that's it, simple as that.

In stock

This valve controls the speed of your tool. Simply turn the knob to your desired speed from shut off to full speed and everything in between. Can be used with tank and tankless air compressors.

In stock
+